Atlas
About
Contents
Glossary
Facebook
Instagram
LinkedIn

Micrography by OM using A262 Method A

1 case · 1 image

Crevice Corrosion in a Subsea System — Aspect Before Analysis

Search & filters

Search

1 image

TryML00084 corrosion ML00014 brittle fracture ductile behavior fatigue hydrogen fracture embrittlement stress corrosion

Browse by category (6)

Application34

Oil and Gas38 cases
Subsea27 cases
O&G Well Drilling19 cases
Ship17 cases
Structure16 cases
Offshore13 cases
Automotive10 cases
Chemical Industry10 cases

+26 more

Boiler9 cases
Energy9 cases
Engine7 cases
Piping7 cases
FPSO6 cases
Mechanical Industry6 cases
Pressure Vessel5 cases
Refinery5 cases
Heat Exchanger4 cases
Lifting4 cases
Maritime4 cases
Siderurgy4 cases
Transportation3 cases
Gas Turbine2 cases
Kitchen2 cases
Valve2 cases
Acquaduct1 case
Fired Heater1 case
Mooring Chain1 case
Ornamental1 case
Petrochemical1 case
Pipeline1 case
Pulp and Paper1 case
Tool1 case
Warlike1 case
Waste Heat Recovery Unit1 case

Microstructure73

Austenite38 cases
Ferritic pearlitic38 cases
Tempered Martensite34 cases
Martensite19 cases
Granular13 cases
Duplex Ferritic Austenitic12 cases
Bainite11 cases
Ferritic11 cases

+65 more

Ferritic Bainitic11 cases
Strain Hardened11 cases
Segregation Bands9 cases
Alpha8 cases
Pearlitic7 cases
Refined ferritic7 cases
Secondary carbides7 cases
Austeno ferritic6 cases
Coating Layer6 cases
Dendritic6 cases
Aged Martensite5 cases
Alpha & Beta5 cases
Ferritic matrix5 cases
Graphite in nodules5 cases
Precipitation Hardened5 cases
Coarse Structure4 cases
Detrimental phases4 cases
Graphite in flakes4 cases
Martensite and Retained Austenite4 cases
Monophasic4 cases
Small amount of delta ferrite4 cases
Surface layer of Thermal Spray4 cases
Acicular Ferrite3 cases
Carburized Layer3 cases
Columnar Grains3 cases
Equiaxial Grains3 cases
Ferritic pearlitic matrix3 cases
Network of Primary Carbides3 cases
Pearlite Highly Strained3 cases
Pearlitic Matrix3 cases
Small Amount of Delta Phase3 cases
Anisotropy2 cases
Bainitic Martensitic2 cases
Coarse Precipitation at Grain Boundaries2 cases
Cored Matrix2 cases
Deformed Structure2 cases
Degradated2 cases
Ferrite and Carbides2 cases
Fine Transgranular Precipitation2 cases
Free from Carbides2 cases

and 25 more not shown here — refine in the Atlas

Standard298

UNS106 cases
ASTM96 cases
A80 cases
AISI37 cases
API16 cases
B15 cases
ALLOY14 cases
NF EN12 cases

+290 more

and 250 more not shown here — refine in the Atlas

Condition60

Damage123 cases
Corrosion39 cases
Sound39 cases
Typical manufacturing28 cases
Fabrication Defect20 cases
Used19 cases
Removed From Service18 cases
Hydrogen17 cases

+52 more

and 12 more not shown here — refine in the Atlas

Product89

Raw Material128 cases
Finished Product113 cases
Welded Joint30 cases
Pipe20 cases
Rolled Plate19 cases
Tube17 cases
Casting16 cases
Fabrication Weld15 cases

+81 more

and 41 more not shown here — refine in the Atlas

Material61

Ferrous Alloys150 cases
Low Alloy Steel56 cases
High Alloy Steel52 cases
Carbon Steel31 cases
Non Ferrous Alloys31 cases
Low Alloy Medium Carbon QT23 cases
Low Carbon Steel21 cases
Austenitic Stainless Steel19 cases

+53 more

and 13 more not shown here — refine in the Atlas

Atlas / Capture method / Optical Microscope / Micrography by OM using A262 Method A

Detail focus: Non Metallic Inclusions ×clear all

Results

SortNewest Oldest Title A-Z Title Z-A

The pin microstructure in the longitudinal section shows austenitic structure, free from carbides, and sulfide inclusions that characterize the free cutting condition of this stainless steel.

77

ML00016 / Apr.2017

SCC in Free Cutting 303SS

M - Austenitic Stainless SteelP - Machined PartAp - OffshoreCd - Stress Corrosion

Cm - Micrography by OM using A262 Method ADf - Non Metallic Inclusions

© copyright. All rights reserved
Version 1.0